How To Thin Paint For Spray Paint (Start To Finish Guide)

If you want to use a spray gun at some point in the near future, you might be concerned about the ease with which the paint will bleed through the device when you do so.

Learning the process of thinning the paint for a spray gun is the ideal thing to do since it eliminates the need to purchase a different kind of paint or worry about harming your HVLP spray gun.

If you learn how to do this, you will never have to worry about either of those things again. It is much simpler to learn the best technique to thin the paint now that there is such a large selection of different paints available, such as encapsulants, acrylic paint, latex paint, and a lot other paints.

This will allow you to avoid continuously switching paints or spray guns. Because of this method, your prices will be reduced, and the lifespan of your spray paint will be increased because you will be using a lesser amount of it.

Continue reading this article if you are interested in learning how to properly adjust the consistency of the paint in your spray gun so that it works properly.

Reason For Using Thinner

You might be curious as to why it is necessary to water down paint before using a sprayer. There are a great number of reasons, and we have jotted down some of them below:

  • Both the ease with which the paint flows and the degree to which it adheres to surfaces are impacted by the paint’s viscosity. Your paint can be thinned down to deal with this problem.
  • By adding water or thinner to the mixture, you will be able to exert greater control over the spray form that the mixture takes. Because of this, it is much simpler to aim and proceed in the same direction while spraying a wall. As a result, you won’t have to move about as much to get into the corners of the room you’re painting. Painting items like doors and windows, which contain a lot of minute details that can be impossible or difficult to achieve otherwise, is made easier with the use of this technique. Because the paint won’t get into the cracks and crevices, you’ll also save time when it comes to cleaning up.
  • If you are using a sprayer, the number of solids that your paint contains may provide some challenges for you. You may ensure that your paint has a sustainable viscosity without any lump by mixing the thinner with the paint. This will accomplish these goals. Additionally, a thinner will remove air from the mixture, allowing it to be atomized and applied across a greater surface area.

Little Considerations Before You Start

How To Know The Right Consistency Of Paint

A viscosity cup is a useful tool for getting an accurate reading of whether or not the paint you are using is too watered down.

This is standard equipment for all spray systems of sufficient grade, and it is useful for determining whether or not problems are occurring as a result of mildew or an inconsistent pattern of spraying.

Pour some of the paint into one end keeping half an inch left in front prior to pouring the rest for testing later; you can see how smooth and even the flow-through is as a result of the correct viscosity.

Paint Too Thin To Work With

Thicker water is preferable to a lack of it. Start by adding little water and stirring thoroughly to ensure that the paint doesn’t just flow out of the bucket when you add more.

As a general rule of thumb, while working on large surfaces like walls or ceilings, you should use around four cups total of paint in order to achieve an even and smooth flow through both funnels.

Basics Of Oil Paint & Thinner

A long-standing industry standard has been the use of oil-based primers and paints. Oil paints provide excellent adhesion, and decent gloss, and are resistant to scrapes and scuffs.

They are also very good at blocking stains and are resistant to scratches and scuffs. Oil-based paints are better at penetrating the surface, leveling, and drying to a better finish than latex paints.

In high concentrations and for lengthy periods of time, they can be dangerous to humans due to their sluggish drying time and large emission of VOCs.

For the purpose of cleaning brushes and applicators after dealing with oil-contained paints, solvents are an absolute prerequisite.

There are fewer fumes released by latex paints since they can be washed with soap and water. To be used in sprayer applicators or when a thinner combination is needed simply for working with, paint thinners are solutions that can help in dissolving paint and lower its viscosity or “thin” the paint.

Using paint dissolvers to clean brushes, rollers and other equipment is a great way to get rid of paint that has built up over time.

An open can of paint will begin to harden, dry, and thicken as it sits in the sun. This is something that can be mitigated by being slimmer. Paint can be removed with a variety of solvents.

Some of the most common solvents are acetone, naptha, MEK, and denatured alcohol. Be sure to read the product labels before using any solvents to make sure you’re using them correctly and to make sure you’re aware of any safety concerns.

Required Supplies

It is helpful to have a clear idea of what you require for a job before you begin planning it out, particularly if the project involves painting a vast area.

Paint can be thinned with a technique that is, fortunately, not overly complicated and does not call for an excessive amount.

  • It goes without saying that you’ll need the paint in order to thin it. There will be no noticeable difference in the color of the surface you are covering if you do not use paint.
  • Latex paints and HVLP spray gun, water is the principal-agent that is employed for thinning. Even if you won’t drink all of the water you bring with you, it is imperative that you bring along a sufficient amount. It is recommended to play it safe and has around half of the paint’s volume diluted in water just in case something goes wrong.
  • In order to determine the paint’s level of thickness, you will need a funnel. This will provide a quick visual depiction for you to refer to in order to ensure that you are maintaining the appropriate consistency.
  • Spray gun
  • It is in your best interest to prepare a test surface to spray the paint that has been thinned. This will allow you to verify that the paint sprays effectively and adheres correctly to the test surface.

How To Thin Paint For Spray Paint – Complete Process

Pick The Right Thinner

You should purchase a solvent or thinner that is suitable for both the kind of paint you are working with and the way you intend to apply it.

For instance, if you are going to use spray paint you will require a paint that is mixed in a thinner consistency. Paint thinners designed for use with latex paints should not be used with oil-contained paints.

It is important to read all of the information and instructions on the label.

Right Amount Of Thinner

Employ just a little bit of the thinner. Be sure to check the labels on paint containers for the suggested ratio of paint-to-paint thinner provided by the manufacturer.

When thinning paint for general purposes, maintain the ratio of 3:1 or 4:1, or a ratio that is comparable is adequate.

It is essential to ensure that the volume of paint is greater than the volume of paint thinner at all times. If it isn’t, the paint can be too thin, which would result in the finished surface having a color tone that is paler than what was desired.

Remember to keep in mind that different kinds of paint as well as different methods of application call for different consistencies and techniques.

For example, in order to prevent the paint gun from becoming clogged, the mixture that is used to spray the paint should be thin.

To properly combine the thinner and the paint, first, follow any and all instructions provided by the manufacturer, then carefully measure out the required quantity of paint, and then transfer it to a mixing bucket.

While stirring with a paint stirrer, slowly add the required amount of thinner until you reach the desired consistency.

Paint and thinner should be mixed together for several minutes, during which time the consistency should be checked occasionally.

Test The Mixture

Using your preferred method, apply multiple layers of the mixture to the appropriate surface before stepping back to assess the results. Make certain that the paint layer thoroughly covers the surface.

If the paint is severely dropping or running, that should be checked out as well! Reapply a little amount of thinner if necessary, and if the paint still isn’t thin enough, thin it further.

Cleaning Process Of Applicators & Brushes

Three-Container Method

As a result of the three-container method, there is less waste and less risk of environmental damage. To begin, determine what kind of paint you’re removing and then select the suitable solvent to remove it.

When painting with oil-based paint, you need to use a paint thinner specifically designed for that purpose. In order to ensure that you made the appropriate purchase, check the product label.

Three containers should be partially filled with solvent. Spin the brush once you’ve removed the majority of the paint from the first container.

It’s time to repeat this process with the second container. The third container should be used to complete the operation.

For a few days, apply the thinner into a tight container and let the paint settle. Use a damp cloth to wipe down your brushes and other equipment before hanging it to dry.

Proper Disposal

If the thinner in the sealed container is clear with all paint particles settled to the bottom, you’re done cleaning your applicators.

Using a permanent marker, label the container with “used thinner” so that it can be reused at a later date. Separate and seal any remaining paint to be disposed of at a hazardous waste facility nearby after it has dried.

Find out where these locations are by contacting your local government.

Final Verdict

Paint isn’t always easy to work with, but if you use spray guns you can see that those are surprisingly durable. When it comes to viscosity, you shouldn’t worry too much if your measurements are not correct.

It is vital to make your paint thin properly so that it does not get stuck in the spray gun; but, as long as you are able to complete your painting job without making any nasty places and without destroying your gun, you will be OK.

Remember to clean the spray gun thoroughly after each time you use it. If you follow the instructions that we have put out here, your life will be a lot simpler, and the outcome of your job should ideally be flawless.

Photo of author

Shelley Stevenson

Shelly Stevenson is the full-time editor responsible for painting, flooring, bathrooms & home climate coverage at StyDomIo. She is a home improvement expert with an eye for design and the skills to get the work done. She knows what turns a house into a home and has the advice and ideas to make upgrades easy and fun.

Leave a Comment

Explore Us

About Us

StayDomIo Logo

At StayDomIo.com, we have a team of professional industry experts to help you find guides on painting, finishing, flooring, bathroom & kitchen to make your home look stunning. We have tested, researched & written hundreds of buying guides to help you select the top notch & affordable product out there!

Disclosure

StayDomIo.Com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.